![]() If the blinking does not stop, we recommend checking the troubleshooting section online with Nutribullet. The same thing will happen when you use an incorrect lid, as it will also trigger the light to blink.Īs soon as you see the blinking light stop the appliance and check if you have the right fitting for the lids and cups, and that everything is aligned. For example, if there are misaligned parts, the light will flash to show it is not safe to use until fixed. When you see the power light blinking, it is a sign of problems with your blender. ![]() If they don’t, you can access the activators through the bottom of the powerbase by unscrewing it. Another great solution is applying vinegar with a Q-tip.Īfter a few minutes, give it another try and they should move. If they do not want to budge, you can use some cooking oil on them or hot water to moisten them. They complete a circuit to ensure safe use of the Nutribullet.įor each of these activators, you should be able to move them downwards. These activators are little switches that get pressed when you connect the cup to the powerbase. We recommend looking for the blender’s plastic activators. This typically happens when the latch between the containers gets stuck. Lastly, there can be a loose extractor blade, and if not screwed on correctly, the fluid runs from your blender. If your Nutribullet starts leaking liquids, it is not a good sign as you may have overfilled it, putting strain on the blades and leading to an overflow.Īnother concern is that external or internal cracks could allow the liquid to travel, and you may need to invest in replacement parts to fix it.Īnother reason for leakage is that the extractor blade seal is damaged, leaving it prone to leak. The last problem is that the blades could be jammed, which happens when you do not clean them properly. Your Nutribullet can also handle liquids, but heavy and dense solids. Sometimes it can also result from placing the wrong foods in the blender as it only slices through softer food like fruit and veggies. When you pass the fill line, the blades cannot slice effectively. Firstly, you may have put too much food inside the cup. Still, if the blades do not cut at all, even when the internal parts move, it can be for different reasons. You can replace the blades with a new set that is sharp enough to slice through the food. The fix is relatively easy as the blades could be old or it has become dull. Sometimes, the blades only partially cut the food, even if you hear the motor running. It may be that it has come loose or there is an issue with the cable/outlet. Check it’s plugged in correctly and check the outlet. If you see any issues, then it may be best to replace the device.Īnother check to do is a simple and obvious one. If it is old, there could be some parts that do not have a protective covering and the wiring or components may have been worn down.įor older Nutribullets, it’s a good idea to remove the casing and make a visual inspection. If it’s not an overheating issue, you need to ask how old your blender is. If you see the blender struggling, give it a short break before finishing the process. If this is a problem, then it’s important not to overfill your Nutribullet and also use it in short bursts. You need to wait for up to an hour before it starts working again. This is often accompanied by a burning smell. This is a common feature of hair dryers but can apply to blenders too. If this happens, then it won’t turn back on until it has cooled down. Many devices will cut out when they get hot to stop them from becoming a fire hazard. The most common is that your blender has overheated. If your blender decides to stop working midway through your smoothie, there can be a few things causing the problem. Here we look at the most common problems. ![]() Sometimes it’s human error whereas other times, there may be something wrong with the device. Yes, a lot can go wrong with your Nutribullet. Why Has My Nutribullet Blade Stopped Spinning? Here we’ll take a close look at why your Nutribullet blades have stopped spinning and what you can do about it. The good news is that most problems with your Nutribullet can be solved fairly easily. There are other potential problems as the blades may not work if you’ve overfilled the cup or if there is another technical issue. If your blender does not spin at all, it is usually due to the device getting too hot or the activators may be stuck. If this happens to you, it can be very frustrating. You add all your ingredients only to find that the blades stop spinning. You want to start your day with a healthy smoothie made in your brilliant Nutribullet. If this doesn’t solve the problem, there is a good chance that the activators are stuck, which is usually an easy fix. Most of the time, a Nutribullet will stop spinning as the motor has overheated and needs to cool down.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |